- 您现在的位置：买卖IC网 > Sheet目录368 > W25Q16DWSFIG (Winbond Electronics)IC FLASH SPI 16MBIT 16SOIC
W25Q16DW
7.2.29
Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, or obtain the devices electronic identification (ID) number.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low,
shifting the instruction code “ABh” and driving /CS high as shown in Figure 28a & 28b. Release from
power-down will take the time duration of t RES1 (See AC Characteristics) before the device will resume
normal operation and other instructions are accepted. The /CS pin must remain high during the t RES1 time
duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure
28. The Device ID values for the W25Q16DW is listed in Manufacturer and Device Identification table. The
Device ID can be read continuously. The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction is
the same as previously described, and shown in Figure 28c & 28d, except that after /CS is driven high it
must remain high for a time duration of t RES2 (See AC Characteristics). After this time duration the device
will resume normal operation and other instructions will be accepted. If the Release from Power-down /
Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals
1) the instruction is ignored and will not have any effects on the current cycle.
/CS
tRES1
Mode 3
0
1
2
3
4
5
6
7
Mode 3
CLK
Mode 0
Mode 0
Instruction (ABh)
DI
(IO 0 )
Power-down current
Figure 28a. Release Power-down Instruction (SPI Mode)
- 54 -
Stand-by current
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W25Q16VSFIG
IC FLASH 16MBIT 80MHZ 16SOIC
W25Q32BVZPIG
IC SPI FLASH 32MBIT 8WSON
W25Q32DWZEIG
IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG
IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG
IC FLASH SPI 4MBIT 8WSON
W25Q64BVSFIG
IC SPI FLASH 64MBIT 16SOIC
W25Q64CVZEIG
IC SPI FLASH 64MBIT 8WSON
W25Q64DWZEIG
IC FLASH SPI 64MBIT 8WSON
相关代理商/技术参数
W25Q16DWSFIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIG
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSSIG
功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q16DWSSIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWZPIG
制造商:Winbond Electronics Corp 功能描述:IC FLASH 16MBIT 104MHZ 8WSON
W25Q16DWZPIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16V
制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI